International journal of advanced manufacturing technology

• 

  Año 2010, Vol. 46, Número 9-12

  • Advances in measurement technology and intelligent instruments for manufacturing engineering.

    Y. Gao, W. Gao, Y. Takaya, M. Krystek

    págs. 843-844

    

  • A spiral scanning probe system for micro-aspheric surface profile measurement.

    A. Shibuya, Y. Arai, Y. Yoshikawa, W. Gao, Y. Nagaike, Y. Nakamura

    págs. 845-862

    

  • Experimental verification of super-resolution optical inspection for semiconductor defect by using standing wave illumination shift.

    S. Usuki, H. Nishioka, S. Takahashi, K. Takamasu

    págs. 863-876

    

  • Estimation method for errors of an aerostatic planar XY stage based on measured profiles errors.

    J. Hwang, C.-H. Park, S.-W. Kim

    págs. 877-884

    

  • Dynamic analysis by FEM for a measurement system to observe viscoelasticity using levitation mass method.

    T. Yamaguchi, Y. Fujii

    págs. 885-892

    

  • A giant magnetostrictive actuator based on use of permanent magnet.

    W. Lei, T. Jiu-bin, Z. Shan

    págs. 893-898

    

  • Dynamic compensation of modeling uncertainties and disturbances of a precision planar motion stage based on sliding mode observer.

    S. Dian, Y. Arai, W. Gao

    págs. 899-913

    

  • Adaptive identification of hysteresis and creep in piezoelectric stack actuators.

    J. Minase, T.-F. Lu, B. Cazzolato, S. Grainger

    págs. 913-922

    

  • Vibration reduction control of a voice coil motor (VCM)-driven actuator for SPM applications.

    J. Jung, W. Youm, S. Lee, K. Park

    págs. 923-930

    

  • Development of a grating disk of a microrotary encoder for measurement of meshing accuracy of microgears.

    S. Kurukawa, Y. Ariura

    págs. 931-944

    

  • A 32×32 temperature and tactile sensing array using PI-copper films.

    Y.-J. Yang, M.-Y. Cheng, S.-C. Shih, X.-H. Huang, C.-M. Tsao, F.-Y. Chang, K.-C. Fan

    págs. 945-956

    

  • Selection of optimum cutting condition of cobalt-based superalloy with GONNS.

    S. Aykut, M. Demetgul

    págs. 957-968

    

  • Force prediction for single point incremental forming deduced from experimental and FEM observations.

    R. Aerens, P. Eyckens, A. Van Bael, J.R. Duflou

    págs. 969-982

    

  • Grey relational analysis coupled with principal component analysis for optimisation design of the process parameters in in-feed centreless cylindrical grinding.

    A.N. Siddiquee, Z.A. Khan, Z. Mallick

    págs. 983-992

    

  • FEA-aided design of multi-stage drawing process and tooling for production of a miniature sheet metal component.

    L.C. Chan, M.W. Fu, N. Li, J. Lu

    págs. 993-1000

    

  • Hybrid (LASER+CNC) process for lubricant groove on linear guides.

    H.M. Shin, H.W. Choi, S.D. Kim

    págs. 1001-1008

    

  • Development of new edge-detection filter based on genetic algorithm: an application to a soldering joint inspection.

    A. Saenthon, S. Kaitwanidvilai

    págs. 1009-1020

    

  • Recommended slicing positions for adaptive direct slicing by image processing technique.

    S. Rianmora, P. Koomsap

    págs. 1021-1034

    

  • The effect of process parameters on machining of magnesium nano alumina composites through EDM.

    K. Ponappa, S. Aravindan, P.V. Rao, J. Ramkumar, M. Gupta

    págs. 1035-1042

    

  • Generation of offset surface for tool path in NC machining through level set methods.

    H. Shen, J. Fu, Z. Chen, Y. Fan

    págs. 1043-1048

    

  • An efficient heuristic for total flowtime minimisation in no-wait flowshops.

    José Manuel Framiñán Torres, M.S. Nagano, J.V. Moccellin

    págs. 1049-1058

    

  • Performance assessment of decision-making units using an adaptive neural network algorithm: one period case.

    M. Anvari, M. Saidi-Mehrabad, A. Azadeh, Mohd Saberi Mohamad

    págs. 1059-1070

    

  • Parameter optimization of time-varying stiffness method for chatter suppression based on magnetorheological fluid-controlled boring bar.

    D. Mei, Z. Yao, T. Kong, Z. Chen

    págs. 1071-1084

    

  • Using TRIZ methods in friction stir welding design.

    H.T. Hsien, J.L. Chen

    págs. 1085-1102

    

  • Mechanistic approach to predict real machining time for milling free-form geometries applying high feed rate.

    R.T. Coelho, A.F. de Souza, A.R. Roger, A.M.Y. Rigatti, A.A. de Lima Ribeiro

    págs. 1103-1112

    

  • The performance of flat end and hemispherical end tools in single-point incremental forming.

    X. Ziran, L. Gao, G. Hussain, Z. Cui

    págs. 1113-1118

    

  • An experimental investigation of cylindrical wire electrical discharge turning process.

    M.J. Haddad, F. Alihoseini, M. Hadi, M. Hadad, A.F. Tehrani, A. Mohammadi

    págs. 1119-1132

    

  • Direct metal laser fabrication: machine development and experimental work.

    J. Yang, H. Ouyang, Yen. Wang

    págs. 1133-1144

    

  • A comparative experimental investigation of deep-hole micro-EDM drilling capability for cemented carbide (WC-Co) against austenitic stainless steel (SUS 304).

    M.P. Jahan, Y.S. Wong, M. Rahman

    págs. 1145-1160

    

  • Slice overlap-detection algorithm for process planning in multiple-material stereolithography.

    H.-C. Kim, J.-W. Choi, E. MacDonald, R. Wicker

    págs. 1161-1170