International journal of advanced manufacturing technology

• 

  Año 2012, Vol. 61, Número 9-12

  • Forward and reverse mappings of the cement-bonded sand mould system using fuzzy logic.

    B. Surekha, P. R. Vundavilli, M. B. Parappagoudar

    págs. 843-854

    

  • A note on �Selection of cutting parameters in side milling operation using graph theory and matrix approach�.

    R.V. Rao

    págs. 855-858

    

  • Influence of slab milling process parameters on surface integrity of HSLA: a multi-performance characteristics optimization.

    P. Goel, Z.A. Khan, A.N. Siddiquee, S. Kamaruddin, R. K. Gupta

    págs. 859-871

    

  • Vibration-assisted filling capability in thin wall investment casting.

    W. Abdul-Karem, N. Green, K.F. Al-Raheem

    págs. 873-887

    

  • Wear study of Ni�WC composite coating modified with CeO2.

    S. Sharma

    págs. 889-900

    

  • Influence of deformation path change on static strain aging of cold rolled steel strip.

    B. Koohbor, S. Serajzadeh

    págs. 901-909

    

  • Erratum to: Load bearing capacity of tool pin during friction stir welding

    A. Arora, M. Mehta, Amitava De, T. DebRoy

    pág. 921

    

  • Vision inspection system for the identification and classification of defects in MIG welding joints.

    G. Senthil Kumar, U. Natarajan, S. S. Ananthan

    págs. 923-933

    

  • On properties at interfaces of friction welded near-nanostructured Al 5083 alloys.

    M. Sahin, N. Balasubramanian, C. Misirli, H. E. Akata, Y. Can, K. Ozel

    págs. 935-943

    

  • Modelling micro geometrical profiles in fused deposition process.

    A. Boschetto, V. Giordano, F. Veniali

    págs. 945-956

    

  • Experimental investigation on the influence of electrochemical micro-drilling by short pulsed voltage.

    Z.-W. Fan, L.-W. Hourng, M.-Y. Lin

    págs. 957-966

    

  • Process parameter selection for selective laser melting of Ti6Al4V based on temperature distribution simulation and experimental sintering.

    B. Song, S. Dong, H. Liao, C. Coddet

    págs. 967-974

    

  • Softness abrasive flow method oriented to tiny scale mold structural surface.

    C. Li, S.-M. Ji, D.-P. Tan

    págs. 975-987

    

  • Polishing of the aluminum sheets with magnetic abrasive finishing method.

    M. Givi, A. Fadaei Tehrani, A. Mohammadi

    págs. 989-998

    

  • ERP: a literature survey.

    E. Nazemi, M.J. Tarokh, G. R. Djavanshir

    págs. 999-1018

    

  • Development of an algorithm for optimum control process to compensate the nozzle wear effect in cutting the hard and tough material using abrasive water jet cutting process.

    M. Zohoor, S.H. Nourian

    págs. 1019-1028

    

  • Development and characterization of a novel piezoelectric-driven stick-slip actuator with anisotropic-friction surfaces.

    Q. S. Zhang, X.B. Chen, Q. Yang, W. J. Zhang

    págs. 1029-1034

    

  • Deformation and stress of a composite�metal assembly.

    C. Dong, L. Kang

    págs. 1035-1042

    

  • Composite fabrication using friction stir processing�a review.

    H. S. Arora, H. Singh, B. K. Dhindaw

    págs. 1043-1055

    

  • Adaptive nonlinear contour coupling control for a machine tool system.

    J. Lee, W. E. Dixon, J. C. Ziegert

    págs. 1057-1065

    

  • Optimization of variable blank holder force trajectory by sequential approximate optimization with RBF network.

    S. Kitayama, K. Kita, K. Yamazaki

    págs. 1067-1083

    

  • ISO manufacturing tolerancing: three-dimensional transfer with analysis line method.

    B. Anselmetti

    págs. 1085-1099

    

  • A genetic algorithm and particle swarm optimization for no-wait flow shop problem with separable setup times and makespan criterion.

    H. Samarghandi, T. Y. ElMekkawy

    págs. 1101-1114

    

  • Non-identical parallel machine scheduling with fuzzy processing times using genetic algorithm and simulation.

    S. Balin

    págs. 1115-1127

    

  • Scheduling in a two-machine flow-shop for earliness/tardiness under learning effect.

    M. C. Isler, B. Toklu, V. Çelik

    págs. 1129-1137

    

  • Analysis of partial trade credit financing in a supply chain by EOQ-based model for decaying items with shortages.

    K. Annadurai, R. Uthayakumar

    págs. 1139-1159

    

  • A DEA approach for comparing solution efficiency in U-line balancing problem using goal programming.

    H. Farkhondeh, R. Hassanzadeh, I. Mahdavi, N. Mahdavi-Amiri

    págs. 1161-1172

    

  • Editorial: Micromachining.

    V.K. Jain, P.K. Jain, P.V. Rao

    págs. 1173-1174

    

  • Fabrication of micro-features and micro-tools using electrochemical micromachining.

    V.K. Jain, S. Kalia, A. Sidpara, V. N. Kulkarni

    págs. 1175-1183

    

  • Drilling of micro-holes on copper using electrochemical micromachining.

    R. Thanigaivelan, R.M. Arunachalam, P. Drukpa

    págs. 1185-1190