International journal of advanced manufacturing technology

• 

  Año 2013, Vol. 66, Número 5-8

  • Application of GONNS to predict constrained optimum surface roughness in face milling of high-silicon austenitic stainless steel

    S. Elhami, M.R. Razfar, M. Farahnakian, A. Rasti

    págs. 975-986

    

  • Value stream mapping and benefit-cost analysis application for value visibility of a pilot project on RFID investment integrated to a manual production control system-a case study

    R. Tabanli, Tijen Ertay

    págs. 987-1002

    

  • An experimental investigation on oil mist characterization used in MQL milling process

    Arnaud Duchosal, René Leroy, Laurent Vecellio, Christophe Louste, N. Ranganathan

    págs. 1003-1014

    

  • Optimization of micro-EDM drilling of inconel 718 superalloy

    Mustafa Ay, U. Çaydas, A. Hasçalik

    págs. 1015-1023

    

  • Improving machinability of Inconel 718 with a new hybrid machining technique

    Taghi Feyzi, S. Safavi

    págs. 1025-1030

    

  • An integrated decision support system for performance assessment and optimization of decision-making units

    A. Azadeh, S. Ghaderi, M. Anvari, H.R. Izadbakhsh, M. Rezaee, Z. Raoofi

    págs. 1031-1045

    

  • An interactive algorithm for multi-objective flow shop scheduling with fuzzy processing time through resolution method and TOPSIS

    Mahdi Nakhaeinejad, Nasim Nahavandi

    págs. 1047-1064

    

  • A methodology for the implementation of automated measuring stations in flexible manufacturing systems

    A. Sanz, I. González, J. Casado, J. Arenas

    págs. 1065-1073

    

  • Tribodynamic modeling of piston compression ring and cylinder liner conjunction in high-pressure zone of engine cycle

    Prakash Mishra

    págs. 1075-1085

    

  • Condition monitoring for the endurance test of automotive light assemblies

    Wei Hu, Qiao Sun, C.K. Mechefske

    págs. 1087-1095

    

  • A multi-agent system for autonomous supply chain configuration

    Farhad Ameri, Christian McArthur

    págs. 1097-1112

    

  • The effects of laser energy density and particle size in the selective laser sintering of polycaprolactone/progesterone specimens: morphology and drug release

    Gean Salmoria, Priscila Klauss, Karine Zepon, Luiz Kanis

    págs. 1113-1118

    

  • Ultrasonic slot machining of a silicon carbide matrix composite

    Erich Bertsche, Kornel Ehmann, Kostyantyn Malukhin

    págs. 1119-1134

    

  • Joint decision making for maintenance and production scheduling of production systems

    Seungchul Lee, Jun Ni

    págs. 1135-1146

    

  • On the processing and morphological aspects of metal fibers based on low-speed multi-tooth dry cutting

    Wei Yuan, Yong Tang, Xiaojun Yang, Bin Liu, Zhenping Wan

    págs. 1147-1157

    

  • Development of a hydroforming setup for deep drawing of square cups with variable blank holding force technique

    Bharatkumar Modi, D. Kumar

    págs. 1159-1169

    

  • Hybrid solution method for resource-constrained project scheduling problem using a new schedule generator

    H. Yoosefzadeh, H. Tareghian

    págs. 1171-1180

    

  • Nanohydroxyapatite synthesized from calcium oxide and its characterization

    Sumit Pramanik, Kamal Kar

    págs. 1181-1189

    

  • Progressive process design of door lock striker with double bosses by the wall-thickening process

    Dae-Cheol Ko, Hong-Seok Choi, Woo-Seok Jang, Byung-Min Kim

    págs. 1191-1199