Applied thermal engineering

• 

  Año 2004, Vol. 24, Número 5

  • Publishers note

    pág. 609

    

  • Underground railway environment in the UK Part 1: Review of thermal comfort

    G. Maidment, J. Missenden, F. Ampofo

    págs. 611-631

    

  • Underground railway environment in the UK Part 2: Investigation of heat load

    G. Maidment, F. Ampofo, J. Missenden

    págs. 633-645

    

  • Underground railway environment in the UK: Part 3: Methods of delivering cooling

    F. Ampofo, J. Missenden, G. Maidment

    págs. 647-659

    

  • Specific cooling power intensification limits in ammonia¿carbon adsorption refrigeration systems

    S.J. Metcalf, R.E. Critoph

    págs. 661-678

    

  • Experimental and theoretical study of the short term response temperature transients in the cylinder walls of a diesel engine at various operating conditions

    D.C. Rakopoulos, G.C. Mavropoulos, E.G. Giakoumis, C.D. Rakopoulos

    págs. 679-702

    

  • Presentation and evaluation of a new type of air supply system in a passenger carriage in China

    Zhiwei Lian, Xiaojiang Ye, Guirong Zhang, Hongmin Liu

    págs. 703-715

    

  • Thermal applicability of two-phase thermosyphons in cooking chambers¿¿experimental and theoretical analysis

    M.B.H. Mantelli, A.K. da Silva

    págs. 717-733

    

  • Effect of regeneration conditions on the adsorption dehumidification process in packed silica gel beds

    Tsair-Wang Chung, Kuei-Sen Chang, Hui-Chun Wang

    págs. 735-742

    

  • On the thermal time constant of structural walls

    P.T. Tsilingiris

    págs. 743-757

    

  • Header design tradeoffs in microchannel evaporators

    Tushar Kulkarni, Keumnam Cho, Clark W. Bullard

    págs. 759-776

    

  • Performance investigation of plain circular and oval tube evaporatively cooled heat exchangers

    Kai Sirén, Ala Hasan

    págs. 777-790

    

  • Prediction of two-phase heat transfer in a 4-pass evaporator bundle using single tube experimental data

    Ralph L. Webb, Mustafa K. Yanik

    págs. 791-811

    

  • Measurement of the temperature distribution on a circular plane fin by infrared thermography technique

    J.C. Solecki, R. Le Gall, R. Bessaih, C. Bougriou

    págs. 813-825

    

  • Analysis of an ejector with environment friendly refrigerants

    A. Selvaraju, A. Mani

    págs. 827-838

    

  • Modelling of a tool during turning: Analytical prediction of the temperature and of the heat flux at the tool¿s tip

    P. Corvisier, M. Lazard

    págs. 839-849

    

  • Numerical analysis of choked refrigerant flow in adiabatic capillary tubes

    P. K. BANSAL, G. Wang

    págs. 851-863

    

  • Development of no valve solar ice maker

    M. Li, C.J. Sun, W.D. Cai, R.Z. Wang

    págs. 865-872

    

  • Analysis of a single cover FRP flat plate collector for treating tannery effluent

    A. Mani, K. Srithar

    págs. 873-883

    

  • Influence of fuel volatility and spray parameters on combustion characteristics and NO_x emission in a gas turbine combustor

    N.Y. Sharma, S.K. Som

    págs. 885-903

    

  • Drying of silica sludge using microwave heating

    A. Idris, K. Khalid, W. Omar

    págs. 905-918

    

  • Energy and exergy analyses of an experimental open-cycle desiccant cooling system

    Murtaza Y¿ld¿r¿m, Melda Özdinç Çarp¿nl¿o¿lu, Mehmet Kano¿lu

    págs. 919-932

    

  • Environmental impact of thermal insulation thickness in buildings

    Kemal Çomakl¿, Bedri Yüksel

    págs. 933-940

    

  • Energetic efficiency of a gas-engine-driven cooling and heating system

    W.Z. Sun, R.Z. Wang, Z.G. Sun

    págs. 941-947