International journal of advanced manufacturing technology

• 

  Año 2007, Vol. 32, Número 7-8

  • A study of the effect of tool cutting edge radius on ductile cutting of silicon wafers.

    K. Liu, X.P. Li, M. Rahman, K.S. Neo, X.D. Liu

    págs. 631-637

    

  • Performance of cryogenically treated tungsten carbide tools in milling operations.

    A.Y.L. Yong, K.H.W. Seah, M. Rahman

    págs. 638-643

    

  • Optimization of machining parameters using genetic algorithm and experimental validation for end-milling operations.

    P. Palanisamy, I. Rajendran, S. Shanmugasundaram

    págs. 644-655

    

  • A workholding optimization model for turning of ring-shaped parts.

    M.S. Kumadi, J. Morehouse, S.N. Melkote

    págs. 656-665

    

  • Finite element optimization of diamond tool geometry and cutting-process parameters based on surface residual stresses.

    W.J. Zong, D. Li, K. Cheng, T. Sun, Y.C. Liang

    págs. 666-674

    

  • An analytical model of the material removal rate between elastic and elastic-plastic deformation for a polishing process.

    T.-R. Lin

    págs. 675-681

    

  • Estimating chemical mechanical polishing pad wear with compressibility.

    P.-L. Tso, R. Hsu

    págs. 682-689

    

  • Quality design of fixture planning for sheet metal assembly.

    B. Li, H. Tang, X. Yang, H. Wang

    págs. 690-697

    

  • Analysis of pin characteristics for a variable geometry mold.

    A. Kirby, L.A. Stauffer

    págs. 698-704

    

  • Generation and suppression of local severe plastic deformation in sectional multi-point forming.

    W. Liu, S.-S. Jia, C.-M. Zhang, M.-Z. Li

    págs. 705-710

    

  • Optimization of the cooling regime of hot-rolled complex beams.

    J.-L. Marcelin

    págs. 711-718

    

  • Numerical and experimental study on the effect of vibration of the tool in ultrasonic assisted EDM.

    M.T. Shervani-Tabar, A. Abdullah, M.R. Shabgard

    págs. 719-731

    

  • Prediction of depth removal in leather surface grit blasting using neural networks and Box-Behnken design of experiments.

    Z. Hu, R. Bicker, C. Marshall

    págs. 732-738

    

  • On-machine measurement using a noncontact sensor based on a CAD model.

    T.J. Ko, J.W. Park, H.S. Kim, S.H. Kim

    págs. 739-746

    

  • Optimal determination of production run and initial settings of process parameters for a deteriorating process.

    A. Rahim, M. Khan

    págs. 747-756

    

  • Control of a permanent magnet synchronous motor with a fuzzy sliding-mode controller.

    C.F.J. Kuo, C.-H. Hsu, C.-C. Tsai

    págs. 757-763

    

  • Analytical research on intellectual control of yarning characteristics for cotton collocation and rotor spinning.

    C.F.J. Kuo, C.-P. Tien, C.-H. Chiu

    págs. 764-773

    

  • Investigating the transfer of techniques for electronic technical support documentation from aerospace to machine tools.

    R.M. Greenough, D. Williams

    págs. 774-779

    

  • Enhancement of performance of Genetic Algorithm for job shop scheduling problems through inversion operator.

    K.S. Amirthagadeswaran, V.P. Arunachalam

    págs. 780-786

    

  • Study of key algorithms in topology optimization.

    K.-T. Zuo, L.-P. Chen, Y.-Q. Zhang, Jingzhou Yang

    págs. 787-796

    

  • Constrained behavior manipulation for interactive assembly in a virtual environment.

    Z. Liu, J. Tan

    págs. 797-810

    

  • Design of a class based storage picker to product order picking system.

    R. Manzini, M. Gamberi, A. Persona, A. Regattieri

    págs. 811-821

    

  • An integrated manufacturing network management framework by using mobile agent.

    C.-Y. Huang, K. Cheng, A. Holt

    págs. 822-833

    

  • An environmental assessment model applied to printed circuit board manufacturing.

    I.K. Hui

    págs. 834-842