International journal of advanced manufacturing technology

• 

  Año 2009, Vol. 43, Número 1-2

  • Determination of the loading path for tube hydroforming process of a copper joint using a fuzzy controller.

    F. Mohammadi, M. Mosavi Mashadi

    págs. 1-10

    

  • Assessment of flank wear and nose radius wear from workpiece roughness profile in turning operation using machine vision.

    H.H. Shahabi, M.M. Ratnam

    págs. 11-21

    

  • An investigation of bell mouthing in precision hole machining with self-piloting tools.

    M. Al-Ata, M.T. Hayajneh

    págs. 22-32

    

  • Three-dimensional stability lobe and maximum material removal rate in end milling of thin-walled plate.

    A. Tang, Z. Liu

    págs. 33-39

    

  • In-process surface roughness prediction system using cutting vibrations in turning.

    David Rodríguez Salgado, Francisco Javier Alonso Sánchez, Inocente Cambero Rivero, Antonio Marcelo Maeso

    págs. 40-51

    

  • Development of a new method to determine bending sequence in progressive dies.

    M.A. Farsi, B. Arezoo

    págs. 52-60

    

  • Self-piercing riveting for aluminium alloys-composites hybrid joints.

    L. Fratini, V.F. Ruisi

    págs. 61-66

    

  • Study on the crushing and hydroforming processes of tubes in a trapezoid-sectional die.

    S. Li, X. Xu, W. Zhang, Z. Lin

    págs. 67-77

    

  • Some studies on temperature profiles in AISI 304 stainless steel sheet during laser beam welding using FE simulation.

    N.S. Shanmugam, G. Buvanashekaran, K. Sankaranarayanasamy, K. Manonmani

    págs. 78-94

    

  • New mask design approach for UV laser micromachining to reduce stitching errors

    E. Mutapcic, P. Iovenitti, J. Hayes

    págs. 95-106

    

  • Modeling of wire electro-discharge machining of TiC/Fe in situ metal matrix composite using normalized RBFN with enhanced k-means clustering technique.

    P. Saha, D. Tarafdar, S.K. Pal, A.K. Srivastava, K. Das

    págs. 107-116

    

  • Effect of delay time on part strength in selective laser sintering.

    P.K. Jain, P.M. Pandey, P.V.M. Rao

    págs. 117-127

    

  • Study on the effect of frequency tracing in ultrasonic-assisted drilling of titanium alloy.

    I. Hsu, C.C. Tsao

    págs. 127-135

    

  • Research on the uncertainties from different form error evaluation methods by CMM sampling .

    C. Cui, S. Fu, F. Huang

    págs. 136-145

    

  • Single machine group scheduling with general linear deterioration to minimize the makespan.

    J.-B. Wang, W.-J. Gao, L.-Y. Wang, D. Wang

    págs. 146-150

    

  • A new parallel genetic algorithm for solving multiobjective scheduling problems subjected to special process constraint.

    Jiaquan Gao, Guixia He, Yushun Wang

    págs. 151-160

    

  • Hybrid metaheuristics for unrelated parallel machine scheduling with sequence-dependent setup times.

    Chun-Lung Chen, Chuen-Lung Chen

    págs. 161-169

    

  • Scheduling sequence-dependent setup time job shops with preventive maintenance.

    B. Naderi, M. Zandieh, S.M.T. Fatemi Ghomi

    págs. 170-181

    

  • Revised dependent siphons.

    D.Y. Chao

    págs. 182-188

    

  • Revised dependent siphons.

    D.Y. Chao

    págs. 189-190

    

  • Towards an improved tool to facilitate simulation modelling of complex manufacturing systems.

    O. Benedettini, Benny Tjahjono

    págs. 191-199

    

  • Dynamic analysis of a two-stage supply chain�a switched system theory approach.

    H. Wang, H. Liu, J.-h. Yang

    págs. 200-210