International journal of advanced manufacturing technology

• 

  Año 2009, Vol. 45, Número 3-4

  • Complex nonlinear behaviors of drilling shaft system in boring and trepanning association deep hole drilling.

    L. Kong, Y. Li, Y. Lu, D. Li

    págs. 211-218

    

  • Finite element simulation of earing defect in deep drawing.

    R.K. Saxena, P. M. Dixit

    págs. 219-233

    

  • Flange forming with combined blanking and extrusion process on sheet metals by FEM and experiments.

    C.H. Cao, L. Hua, S.L. Liu

    págs. 234-244

    

  • A case-based and practical approach for multivariate modeling of grinding process.

    I. Mukherjee, P.K. Ray

    págs. 245-260

    

  • Research on thermal stress, deformation, and fatigue lifetime of the rapid heating cycle injection mold.

    X. Li, G. Zhao, Y. Guan, H. Li

    págs. 261-275

    

  • Application of PCA-based hybrid Taguchi method for correlated multicriteria optimization of submerged arc weld: a case study.

    S. Datta, G. Nandi, A. Bandyopadhyay, P. Kumar

    págs. 276-286

    

  • A linear piezo-electric ultrasonic motor using a single flexural vibrating bar for electro-discharge system industrial applications.

    M. Shafik, E.M. Shehab, H.S. Abdalla

    págs. 287-299

    

  • Development of an intelligent process model for EDM.

    S.N. Joshi, S.S. Pande

    págs. 300-317

    

  • Direct milling of polymethylmethacrylate for cranioplasty applications.

    D.D. da Costa, Helio Pedrini, O. Bazan

    págs. 318-325

    

  • An efficient approximate profiling method for the rack gear tool.

    N. Oancea, V. Teodor, I. Popa, V. Oancea

    págs. 326-335

    

  • Single-machine scheduling with a sum-of-processing-time based learning effect and deteriorating jobs.

    L.-Y. Wang, J.-B. Wang, D. Wang, N. Yin, X. Huang, E.-M. Feng

    págs. 336-340

    

  • Cause-selecting control charts based on Huber's M-estimator.

    S. Asadzadeh, A. Aghaie

    págs. 341-351

    

  • Development of a continuous fabrication system for a metallic sandwich plate with a three-dimensional truss core.

    Carl Gustav Jung, D.Y. Seung, D.Y. Yang, S.J. Na, D.-G. Ahn

    págs. 352-361

    

  • Multi-response optimisation of sintering parameters of Al�Si alloy/fly ash composite using Taguchi method and grey relational analysis.

    H.S. Jailani, A. Rajadurai, B. Mohan, A.S. Kumar, T. Somakumar

    págs. 362-369

    

  • Optimization of delamination factor in drilling medium-density fiberboards (MDF) using desirability-based approach.

    S. Prokash, K. Palanikumar, N. Manoharan

    págs. 370-381

    

  • A method to exchange the demand of products for cost improvement.

    S. Sharma

    págs. 382-388

    

  • Multi-objectives optimal model of heavy equipment using improved Strength Pareto Evolutionary Algorithm.

    Z. Wei, D. Yang, X. Wang, J. Wang

    págs. 389-396

    

  • Direct minimal empty siphon computation using MIP.

    D.Y. Chao

    págs. 397-405

    

  • A general fuzzy TOPSIS model in multiple criteria decision making.

    I. Mahdavi, A. Heidarzade, B. Sadeghpour-Gildeh, N. Mahdavi-Amiri

    págs. 406-420